View ADL5592-EVALZ_4319509.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

250 MHz to 2400 MHz RF Variable Gain Amplifier ADL5592
FEATURES
Output frequency range: 250 MHz to 2400 MHz Noise figure: 5.7 dB at 1960 MHz OIP3 at 1960 MHz: 29 dBm at PIN = 0 dBm per tone 2 digital attenuators, each with 31 dB range 1 dB attenuation step size Single SPI port Single supply: 4.5 V to 5.5 V 40-lead, 6 mm x 6 mm LFCSP package
FUNCTIONAL BLOCK DIAGRAM
RFOUT RFIN
LOIP LOOP EN
ATTENUATOR CONTROL CIRCUITRY
ADL5592
LOOP OUT SPI PORT*
06662-001
APPLICATIONS
GSM/EDGE and cellular communications systems
*COMPRISES THE DATA, CLK, AND LE PINS.
Figure 1.
GENERAL DESCRIPTION
The ADL5592 is a digitally programmable variable gain amplifier (VGA) designed for use from 250 MHz to 2400 MHz. Two digitally programmable attenuators are cascaded with a high linearity fixed-gain amplifier. The device also includes a mixer, which can be used to mix the transmitted signal into an adjacent receive band for loopback testing. The ADL5592 can be used in conjunction with a direct-to-RF modulator, such as ADL537x and ADL539x, in cellular communications systems such as GSM/EDGE. The ADL5592 is available in a 6 mm x 6 mm, 40-lead exposedpaddle LFCSP package. The device operates from the -40C to +85C temperature range.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2008 Analog Devices, Inc. All rights reserved.
ADL5592 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 Functional Block Diagram .............................................................. 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 6 ESD Caution .................................................................................. 6 Pin Configuration and Function Descriptions ............................. 7 Typical Performance Characteristics ............................................. 8 Theory of Operation ...................................................................... 11 Input Switch ................................................................................ 11 Digital Attenuator....................................................................... 11 SPI Interface ................................................................................ 11 Fixed-Gain Amplifier................................................................. 11 Loopback Mixer.......................................................................... 11 Applications Information .............................................................. 12 Basic Connections ...................................................................... 12 Programming the SPI Port ........................................................ 12 GSM/EDGE Transmit Application .......................................... 14 Soldering Information ............................................................... 14 Evaluation Board ............................................................................ 15 Characterization Setup .............................................................. 15 Schematic and Layout ................................................................ 16 Configuration Options .............................................................. 18 Outline Dimensions ....................................................................... 19 Ordering Guide .......................................................................... 19
REVISION HISTORY
6/08--Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADL5592 SPECIFICATIONS
Measured at VCC = 5.0 V, TA = 25C, unless otherwise noted. Table 1.
Parameter OPERATING FREQUENCY RANGE DIGITAL ATTENUATORS--fRF = 460 MHz to 496 MHz Attenuation Range Attenuator Step Size Relative Step Accuracy Absolute Step Accuracy Step Size Variation vs. Frequency Dynamic Range Variation vs. Temperature VGA RF Output Power vs. Frequency Gain vs. Temperature vs. Frequency OIP3 Noise Figure Return Loss Modulation Spectrum Conditions Min 250 Typ Max 2400 Unit MHz
28
Variation within transmit band TA = 0C to 85C RFIN = 4 dBm, minimum attenuation Variation within transmit band Minimum attenuation, 270 nH choke inductor Variation within TA = 0C to 85C Variation within transmit band Two tones with = 1 MHz, 0 dBm per input tone Minimum attenuation RFIN at minimum attenuation RFOUT at minimum attenuation Relative to carrier in 30 kHz, POUT = 12 dBm, 8 PSK, 270 nH choke inductor 400 kHz carrier offset 600 kHz carrier offset 1.2 MHz carrier offset POUT = 12 dBm, 8 PSK RMS Peak
30.5 1 -0.02 0.4 -0.02 0.6 16.3 0.02 12.3 1 0.02 27.7 4.3 -10 -15
1.0 4.0
dB dB dB dB dB dB dBm dB dB dB dB dBm dB dB dB
8
-72 -85 -88 0.7 2.1
dBc dBc dBc % %
Error Vector Magnitude (EVM)
DIGITAL ATTENUATORS--fRF = 869 MHz to 960 MHz Attenuation Range Attenuator Step Size Relative Step Accuracy Absolute Step Accuracy Step Size Variation vs. Frequency Dynamic Range Variation vs. Temperature RFOUT Power vs. Frequency Gain vs. Temperature vs. Frequency OIP3 Noise Figure Return Loss Modulation Spectrum
28
Variation within transmit band TA = 0C to 85C RFIN = 4 dBm, minimum attenuation Variation within transmit band Minimum attenuation, 270 nH choke inductor Variation within TA = 0C to 85C Variation within transmit band Two tones with = 1 MHz, 0 dBm per input tone Minimum attenuation RFIN at minimum attenuation RFOUT at minimum attenuation Relative to carrier in 30 kHz, POUT = 12 dBm, 8 PSK 270 nH choke inductor 400 kHz carrier offset 600 kHz carrier offset 1.2 MHz carrier offset
Rev. 0 | Page 3 of 20
30.1 1 -0.03 0.5 -0.03 0.6 14.8 0.2 10.8 1.3 0.2 28.5 4.8 -9.8 -9.8
1.0 4.0
dB dB dB dB dB dB dBm dB dB dB dB dBm dB dB dB
8
-72 -84 -88
dBc dBc dBc
ADL5592
Parameter Error Vector Magnitude (EVM) Conditions POUT = 12 dBm, 8 PSK RMS Peak Min Typ 0.9 2.7 Max Unit % %
DIGITAL ATTENUATORS--fRF = 1805 MHz to 1990 MHz Attenuation Range Attenuator Step Size Relative Step Accuracy Absolute Step Accuracy Step Size Variation vs. Frequency Dynamic Range Variation vs. Temperature RFOUT Power vs. Frequency Gain vs. Temperature vs. Frequency OIP3 Noise Figure Return Loss Modulation Spectrum
28
Variation within transmit band TA = 0C to 85C RFIN = 4 dBm, minimum attenuation Variation within transmit band Minimum attenuation, 33 nH choke inductor Variation within TA = 0C to 85C Variation within transmit band Two tones with = 1 MHz, 0 dBm per input tone Minimum attenuation RFIN at minimum attenuation RFOUT at minimum attenuation Relative to carrier in 30 kHz, POUT = 12 dBm, 8 PSK 33 nH choke inductor 400 kHz carrier offset 600 kHz carrier offset 1.2 MHz carrier offset POUT = 12 dBm, 8 PSK RMS Peak
30.5 1 -0.02 0.24 -0.02 0.7 12.9 0.2 8.9 1.5 0.2 29 5.7 -16.4 -11.1
1.0 4.0
dB dB dB dB dB dB dBm dB dB dB dB dBm dB dB dB
8
-71 -86 -88 0.7 1.9 13
dBc dBc dBc % % MHz V V MHz MHz dB dB dB MHz dBm dBm dBm dBm dB dB dBm dBm dBm dBc/Hz V
Error Vector Magnitude (EVM)
LOGIC INPUTS Clock Speed Input Logic Low Input Logic High RF LOOP MIXER Input Frequency Output Frequency Input Return Loss Output Return Loss LOIP Frequency Range LOIP Power LOOP OUT Power
DATA, CLK, LE 2.5 460 450 RFIN with loop enable active low at 1960 MHz LOIP at 80 MHz LOOP OUT at 1880 MHz 10 -6 RFIN = 5 dBm 450 MHz to 486 MHz 824 MHz to 915 MHz 1710 MHz to 1910 MHz Within a received band Variation within TA = 0C to 85C Two tones with = 1 MHz, 0 dBm per input tone 450 MHz to 486 MHz 824 MHz to 915 MHz 1710 MHz to 1910 MHz Carrier offset > 400 kHz
Rev. 0 | Page 4 of 20
0.8
1990 1910 -13 -16 -8 95 0 -13.0 -12.1 -13.1 0.6 1.1 13.8 13 10.1 -132
Output Power Flatness vs. Frequency vs. Temperature OIP3
Output Noise Density Loop Enable Control
ADL5592
Parameter Input Logic Low Input Logic High Switching Time ISOLATION LOOP OUT to RFOUT Conditions Loopback active Loopback inactive Enable/disable Loopback mode, at loop output frequency, maximum attenuation set on ATTN 1 and ATTN 2. RFIN = 4 dBm, RF loop output = -11 dBm Loopback mode, at RF input frequency, maximum attenuation set on ATTN 1 and ATTN 2. RFIN = 4 dBm, RF loop output = -11 dBm At carrier frequency, transmit mode, minimum attenuation set on ATTN 1 and ATTN 2, POUT = 15 dBm Transmit mode, maximum attenuation set on ATTN 1 and ATTN 2, PINATT1 = 4 dBm VCC pins 4.5 Loopback active at TA = 25C TA = -40C to +85C Loopback inactive at TA = 25C TA = -40C to +85C Min 2.4 Typ 0 5 Max 0.8 500 -68 Unit V V ns dBm
RFIN to RFOUT
-50
dBm
RFOUT to LOOP OUT RFIN to LOOP OUT POWER SUPPLIES Voltage Supply Current
-50 -50
dB dB
5.0 230 255 189 208
5.5
V mA mA mA mA
Rev. 0 | Page 5 of 20
ADL5592 ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Supply Voltage VCC RFIN LOIP LOOP EN, DATA, CLK, LE Internal Power Dissipation JA (Exposed Paddle Soldered Down) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Rating 5.5 V 15 dBm 10 dBm 5.5 V 1650 mW 47C/W 150C -40C to +85C -65C to +150C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
Rev. 0 | Page 6 of 20
ADL5592 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
LOIP 1 LOIN 2 VCC 3 LOOP OUT 4 LOOP EN 5 DATA 6 CLK 7 LE 8 DVCC 9 GND 10
40 39 38 37 36 35 34 33 32 31 NC RFIN GND GND NC GND NC NC GND NC*
ADL5592
(Not to Scale)
30 29 28 27 26 25 24 23 22 21
GND NC NC* NC GND GND GND NC GND VCC
*THE PADS FOR PIN 28 AND PIN 31 MUST REMAIN FREE OF TRACES TO AVOID STRAY CAPACITANCE. NOTES 1. NC = NO CONNECT 2. CONNECT EXPOSED PADDLE TO A LOW IMPEDANCE GROUND PLANE.
06662-002
Figure 2. Pin Configuration (Top View)
Table 3. Pin Function Descriptions
Pin No. 1 2 3, 21 4 5 6 7 8 9 12 39 10, 11, 13, 14, 17, 19, 22, 24 to 26, 30, 32, 35, 37, 38 15, 16, 18, 20, 23, 27 to 29, 31, 33, 34, 36, 40 Mnemonic LOIP LOIN VCC LOOP OUT LOOP EN DATA CLK LE DVCC RFOUT RFIN GND Description Loopback Mixer Differential LO Input. Should be ac-coupled to the source of the mixer local oscillator signal. Loopback Mixer Differential LO Input. Should be ac-coupled to ground. Positive Supply. Nominally equal to 5 V. VCC and DVCC must be connected together externally and be properly bypassed. Loopback Mixer RF Output. Single-ended 50 output. Loopback Mixer Enable. Apply logic high for normal transmit mode. Apply logic mode low for loopback mode. SPI Data Input. Both attenuators are programmed with a single 10-bit word. SPI Clock Input. Data is clocked on the rising edge of CLK. SPI Latch Enable. Data is latched on the falling edge of LE. Digital Positive Supply. Nominally equal to 5 V. RF Output. Should be ac-coupled. RF Input. Should be ac-coupled. Common. Connect to a low impedance ground plane.
NC
No Connection. The pad for Pin 28 and Pin 31 must remain free of traces to avoid stray capacitances.
EP
Exposed Paddle. Connect to a low impedance ground plane.
Rev. 0 | Page 7 of 20
GND RFOUT GND GND NC NC GND NC GND NC
11 12 13 14 15 16 17 18 19 20
ADL5592 TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25C, VS = 5.0 V, unless otherwise noted.
20 10 0 0dB 40
OUTPUT THIRD-ORDER INTERCEPT (dBm)
35
-40C -25C 0C +25C +85C
GAIN (dB)
-10 -20 -30 -40 -50 250 31dB
30
25
06662-003
500
750
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
500
750
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
Figure 3. Gain vs. Frequency by Gain Code, All Input Attenuator (ATTN 1) Code Steps
Figure 6. Output Third-Order Intercept vs. Frequency Across Temperature, Maximum Gain, 0 dBm per Input Tones with 1 MHz Spacing
20 10 0
0dB
OUTPUT P1dB COMPRESSION (dBm)
30
25
-40C -25C 0C +25C +85C
GAIN (dB)
-10 -20 -30 -40 -50 250 31dB
20
15
06662-004
500
750
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
500
750
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
Figure 4. Gain vs. Frequency by Gain Code, All Output Attenuator (ATTN 2) Code Steps
Figure 7. Output P1dB Compression vs. Frequency Across Temperature, Maximum Gain
0 -5 -10
10
20
8
NOISE FIGURE (dB)
16 NOISE FIGURE
GAIN (dB)
06662-008
RETURN LOSS (dB)
-15 -20 -25 -30 -35 -40 -45 -50 250 500 750 RFIN 0dB ATTENUATION RFIN 31dB ATTENUATION RFOUT 0dB ATTENUATION RFOUT 31dB ATTENUATION LOOP OUT
06662-005
6
12
4
GAIN
8
2
4
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
0 250
500
750
1000 1250 1500 1750 FREQUENCY (MHz)
2000
2250
0
Figure 5. Return Loss vs. Frequency, RFIN, RFOUT, and LOOP OUT
Figure 8. Noise Figure and Gain vs. Frequency, at Maximum Gain
Rev. 0 | Page 8 of 20
06662-007
10 250
06662-006
20 250
ADL5592
0.4 0.3
RELATIVE STEP ACCURACY (dB)
ABSOLUTE STEP ACCURACY (dB)
0.2 0.1 0 -0.1 -0.2 -0.3
-40C -25C 0C +25C +85C
2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 -0.25
06662-009
-40C -25C 0C +25C +85C
ATTENUATOR 1 -0.4 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE 32
ATTENUATOR 1 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE 32
06662-012 06662-014 06662-013
-0.50
Figure 9. Gain Step Error Across Temperature, Frequency = 492 MHz (Each Attenuator Is Swept Independently from 0 to 31)
Figure 12. Absolute Gain Error Across Temperature, Frequency = 492 MHz (Each Attenuator Is Swept Independently from 0 to 31)
0.4 0.3
RELATIVE STEP ACCURACY (dB)
ABSOLUTE STEP ACCURACY (dB)
0.2 0.1 0 -0.1 -0.2 -0.3
-40C -25C 0C +25C +85C
1.75 1.50 1.25 1.00 0.75 0.50 0.25 0
06662-010
-40C -25C 0C +25C +85C
ATTENUATOR 1 -0.4 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE 32
ATTENUATOR 1 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE 32
-0.25
Figure 10. Gain Step Error Across Temperature, Frequency = 925 MHz (Each Attenuator Is Swept Independently from 0 to 31)
Figure 13. Absolute Gain Error Across Temperature, Frequency = 925 MHz (Each Attenuator Is Swept Independently from 0 to 31)
0.4 0.3
RELATIVE STEP ACCURACY (dB)
ABSOLUTE STEP ACCURACY (dB)
0.2 0.1 0 -0.1 -0.2 -0.3
-40C -25C 0C +25C +85C
2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 -0.25 32
06662-011
-40C -25C 0C +25C +85C
ATTENUATOR 1 -0.4 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE
ATTENUATOR 1 0 8 16 24 GAIN CODE 32 0
ATTENUATOR 2 8 16 24 GAIN CODE 32
-0.50
Figure 11. Gain Step Error Across Temperature, Frequency = 1960 MHz (Each Attenuator Is Swept Independently from 0 to 31)
Figure 14. Absolute Gain Error Across Temperature, Frequency = 1960 MHz (Each Attenuator Is Swept Independently from 0 to 31)
Rev. 0 | Page 9 of 20
ADL5592
14 492.4MHz 12 925.2MHz 10 1960MHz
GAIN (dB)
8 6 4 2 0 4.50
4.75
5.00 SUPPLY VOLTAGE (V)
5.25
5.50
Figure 15. Gain vs. Supply Voltage at Maximum Gain
06662-015
Rev. 0 | Page 10 of 20
ADL5592 THEORY OF OPERATION
Figure 16 shows a simplified schematic of the ADL5592.
RFOUT RFIN
state (n dB). The various combinations of the five blocks provide the attenuation states from 0 dB to 31 dB, in 1 dB increments.
SPI INTERFACE
ATTENUATOR CONTROL CIRCUITRY
LOIP LOOP EN
ADL5592
LOOP OUT SPI PORT*
06662-016
*COMPRISES THE DATA, CLK, AND LE PINS.
The ADL5592 includes a SPI-compatible, 3-wire serial interface. The Si CMOS interface internally level-shifts the SPI signals, which are used to program a 10-bit shift register and to control the loading of a 10-bit parallel latch. The outputs of the latch are fed into drivers, which convert the logic-level outputs of the latches to signals appropriate for driving the attenuators.
Figure 16. Simplified Schematic
FIXED-GAIN AMPLIFIER
The output of the input attenuator (ATTN 1) is connected to a fixed-gain amplifier that drives the output attenuator (ATTN 2). Because the passive attenuators are linear and contribute minimal noise, the fixed-gain amplifier is the major source of nonlinear distortion and noise. This results in a constant OIP3 and noise figure throughout the different attenuation stages. The fixed-gain amplifier provides 14 dB of gain and broadband, 50 , singleended input and output impedances.
INPUT SWITCH
The high performance single-pole, double throw (SPDT) GaAs pHEMT switch is connected to the RF input pin of the ADL5592 to switch the input signal between the VGA and the mixer. To diminish the impact of the switch on the performance of the VGA and the mixer, this SPDT switch exhibits low insertion loss and high isolation in the operating frequency range. The switch-state control signal is provided by a Si CMOS control circuit.
DIGITAL ATTENUATOR
The digital attenuator consists of five attenuation blocks--1 dB, 2 dB, 4 dB, 8 dB, and 16 dB--each separately controlled by a Si CMOS control circuit. Each attenuation block consists of field effect transistor (FET) switches and resistors that form either a pi- or a T- shaped attenuator. By controlling the states of the FET switches through the Si CMOS control lines, each attenuation block can be set to be in the pass state (0 dB) or the attenuation
LOOPBACK MIXER
The loopback mixer is a Si CMOS Gilbert-cell mixer designed to provide 10 MHz to 100 MHz of frequency translation from the RF input to the mixer output. The mixer has 50 loads at the output for a broadband, single-ended output. The input is fed from the SPDT GaAs pHEMT switch. The overall mixer gain is typically -17 dB. The mixer LO input is designed to operate from 10 MHz to greater than 100 MHz.
Rev. 0 | Page 11 of 20
ADL5592 APPLICATIONS INFORMATION
RF INPUT 1000pF 0.1F LO INPUT
RFIN
GND
GND
GND
GND
NC
0.1F VPOS 0.1F 1000pF LOOP OUT MIXER ENABLE SPI DATA SPI CLOCK SPI LATCH VPOS 0.1F 100pF 100pF LOIP LOIN VCC LOOP OUT LOOP EN DATA CLK LE DVCC GND
NC
NC
GND NC NC NC GND GND GND NC GND VCC VPOS 100pF 10F CHOKE INDUCTOR (COILCRAFT 0603CS) 33nH FOR 1800MHz, 1900MHz BANDS 270nH FOR 450MHz, 850MHz, 900MHz BANDS
NC
ADL5592
RFOUT
GND
GND
NC
GND
GND
GND
NC
NC
RF OUTPUT
Figure 17. Basic Connections
BASIC CONNECTIONS
Figure 17 shows the basic connections for the ADL5592. A single power supply between 4.75 V and 5.25 V is applied to the VCC pins. All the VCC pins must be connected to the same potential. Each power supply pin should be decoupled using a 100 pF capacitor in addition to either a 0.1 F or 10 F capacitor. These capacitors should be located as close as possible to the device. One of the supply pins (Pin 21) also requires biasing of an open-collector using an RF choke (Coilcraft 0603CS). The value of the inductor is dictated by the frequency band of operation: 270 nH for the 450 MHz, 850 MHz, and 900 MHz bands and 33 nH for the 1800 MHz and 1900 MHz bands. The RFIN, RFOUT, and LOOP OUT pins have 50 impedances and must be ac-coupled.
PROGRAMMING THE SPI PORT
Both attenuators are programmed with a single 10-bit word. Figure 18 shows the input and output attenuators, ATTN 1 and ATTN 2, respectively. Table 4 lists the 10-bit words corresponding to the various gain levels. The five least significant bits (LSBs) set the input attenuator, ATTN 1. The five most significant bits (MSBs) set the output attenuator, ATTN 2.
RFIN ATTN 1 AMP ATTN 2 RFOUT
06662-018
Figure 18. Block Diagram of Attenuator Chain
Figure 19 shows the timing diagram of the SPI port transmission. DATA is clocked on the rising edge of CLK. The data is latched and the attenuation is updated on the falling edge of LE (the latch enable pin). The timing requirements indicated in Figure 19 are described in Table 5.
Rev. 0 | Page 12 of 20
06662-017
1000pF
NC
NC
ADL5592
1 LE 0 1 CLK 0
t0 t1 t2 t3
1 DATA 0
D0 LOAD DATA INTO SERIAL REGISTER ON RISING EDGE.
D9 TRANSFER DATA FROM SERIAL REGISTER TO PARALLEL LATCHES ON LE FALLING EDGE.
06662-019
Figure 19. Timing Diagram of SPI Port Transmission
Table 4. 10-Bit Gain Words for SPI Port
ATTN 2
D9 D8 D7 D6 D5 D4 D3
ATTN 1
D2 D1 D0
0 0 0 0 0 1 1 0 0 0 0 0 0 1
0 0 0 0 1 0 1 0 0 0 0 0 0 1
0 0 0 1 0 0 1 0 0 0 0 0 0 1
0 0 1 0 0 0 1 0 0 0 0 0 0 1
0 1 0 0 0 0 1 0 0 0 0 0 0 1
0 0 0 0 0 0 0 0 0 0 0 1 1 1
0 0 0 0 0 0 0 0 0 0 1 0 1 1
0 0 0 0 0 0 0 0 0 1 0 0 1 1
0 0 0 0 0 0 0 0 1 0 0 0 1 1
0 0 0 0 0 0 0 1 0 0 0 0 1 1
ATTN 1 (dB) 0 0 0 0 0 0 0 1 2 4 8 16 31 31
Resulting Attenuation ATTN 2 (dB) Total Attenuation (dB) 0 0 1 1 2 2 4 4 8 8 16 16 31 31 0 1 0 2 0 4 0 8 0 16 0 31 31 62
Table 5. Timing Requirements for the SPI Port
Mnemonic t0 t1 t2 t3 fCLK Description Latch enable setup time. Time between latch enable active (high) and first rising edge of serial clock. Serial data setup time. Time between valid serial data and rising clock edge. Note that this time applies to all bits in the serial data stream Serial data hold time. Time after rising clock edge during which the serial data line cannot change in value. Note that this time applies to all bits in the serial data stream Latch enable hold time. Time after final falling clock edge during which the latch enable must remain active (high). Clock period. Min 15 15 15 15 15 Max Unit ns ns ns ns MHz
Rev. 0 | Page 13 of 20
ADL5592
GSM/EDGE TRANSMIT APPLICATION
Figure 20, Figure 21, and Figure 22 show effects of different input power levels on the spectral mask and EVM. The gain code is held constant at the minimum attenuation (corresponding to Code 0 for both attenuators). At low output power levels, both the spectral mask and EVM remain flat. At higher output power levels, however, the spectral mask expands and the EVM increases. At an output of 12 dBm at 925.5 MHz, the peak and rms EVM are 0.56% and 1.51%, respectively. The spectral mask offsets at 400 kHz, 600 kHz, and 1.2 MHz sit at -72.2 dBc, -84.8 dBc, and -88.01 dBc, respectively. Note that the minimum attenuation setting results in the highest spectral mask and EVM values (excluding noise floor limitations). Increasing the input attenuation of ATTN 1 causes less power to be presented to the amplifier stage. Therefore, the levels of the spectral mask and EVM decrease as the input attenuation of ATTN 1 is increased. As the output attenuation of ATTN 2 is increased, the levels of the spectral mask and EVM remain flat.
0 -10 -20 10 9 8 PEAK EVM 7
SPECTRAL MASK (dB)
-30 -40 -50 -60 -70 -80 -90 600kHz OFFSET 400kHz OFFSET
5 4 3 RMS EVM 2 1 10.0 12.5 OUTPUT (dBm) 15.0
Figure 20. EVM and Spectral Mask vs. Output Power, 488.8 MHz EDGE Signal, 270 nH RF Choke, Minimum Attenuation
0 -10 -20 10 9 8 7 PEAK EVM
SPECTRAL MASK (dB)
-30 -40 -50 -60 -70 -80 -90 600kHz OFFSET RMS EVM 400kHz OFFSET
10.0
12.5 OUTPUT (dBm)
15.0
Figure 21. EVM and Spectral Mask vs. Output Power, 925.5 MHz EDGE Signal, 270 nH RF Choke, Minimum Attenuation
0 -10 -20 10 9 8 7
SPECTRAL MASK (dB)
-30 -40 -50 PEAK EVM -60 -70 -80 -90 600kHz OFFSET RMS EVM 400kHz OFFSET
5 4 3 2 1 10.0 12.5 OUTPUT (dBm) 15.0
Figure 22. EVM and Spectral Mask vs. Output Power, 1960 MHz EDGE Signal, 33 nH RF Choke, Minimum Attenuation
Rev. 0 | Page 14 of 20
06662-022
-100 7.5
1.2MHz OFFSET
0 17.5
EVM (%)
6
06662-021
On the underside of the chip scale package, there is an exposed compressed paddle. This paddle is internally connected to the chip's ground. Solder the paddle to the low impedance ground plane on the printed circuit board to ensure specified electrical performance and to provide thermal relief. It is also recommended that the ground planes on all layers under the paddle be stitched together with vias to reduce thermal impedance.
5 4 3 2 1 1.2MHz OFFSET 0 17.5
-100 7.5
EVM (%)
SOLDERING INFORMATION
6
06662-020
-100 7.5
1.2MHz OFFSET
0 17.5
EVM (%)
6
ADL5592 EVALUATION BOARD
CHARACTERIZATION SETUP
The primary setup used to characterize the ADL5592 is shown in Figure 23. This setup was used to measure the frequency response, linearity, and output compression of the amplifier. A Rohde & Schwarz SMT 03 signal generator was used to drive the amplifier with a 4 dBm input. The output of the ADL5592 was connected to a Rohde & Schwarz FSIQ7 spectrum analyzer through an RF switch matrix unit. For the linearity measurement, two SMT 03 signal generators were used to generate the two-tone RF input signal. (The same SMT 03 is used for both amplifier and mixer characterization.) The gain control data was generated by a Tektronix DG2020A data generator. The DG2020A generated all three of the SPI input signals: CLK, DATA, and LE. A separate SMT 03 was used to generate the mixer local oscillator signal (LO input signal) when the loopback mixer was enabled. An Agilent Visual Engineering Environment (VEE) program controlled the test instruments through the general-purpose interface bus (GPIB) interface.
R&S SMT 03 SIGNAL GENERATOR RFIN LOIP R&S SMT 03 SIGNAL GENERATOR
ADL5592
RFOUT LOOP OUT VCC
R&S FSIQ7 SPECTRUM ANALYZER
RF SWITCH
DATA CLK LE
GPIB INTERFACE INSTRUMENT CONTROLLER
Figure 23. Characterization Bench Setup
Rev. 0 | Page 15 of 20
06662-026
TEKTRONIX DG2020A DATA GENERATOR
AGILENT 6624A DC POWER SUPPLY
ADL5592
SCHEMATIC AND LAYOUT
Figure 24 shows the schematic and Figure 25 and Figure 26 show the layout of the ADL5592 evaluation board. The board is powered by a single supply in the 4.75 V to 5.25 V range. Each power supply pin should be decoupled using a 100 pF capacitor in addition to either a 0.1 F or 10 F capacitor. Table 6 details the various configuration options of the evaluation board.
C2A 0.1F LOPA C3A 0.1F VPOS C7A 0.1F R5A 0 C6A 100pF LOIP C1A 1000pF LBENBA SW1A R12A 10k R8A 0 0 0 TO HEADER R11A 0 VPOS LOIN VCC LOOP OUT LOOP EN DATA CLK LE DVCC
RFOUT GND GND GND GND GND NC NC NC NC
The RFIN, RFOUT, and LOOP OUT pins have 50 impedances and must be ac-coupled. One of the supply pins (Pin 21) requires supply biasing using an RF choke (Coilcraft 0603CS). The value of the inductor is dictated by the frequency band of operation: 270 nH for the 450 MHz, 850 MHz, and 900 MHz bands and 33 nH for the 1800 MHz and 1900 MHz bands.
IN_ATTA
C17A 1000pF
C9A OPEN
RFIN
GND
GND
GND
GND
NC
NC
NC
NC
MX_OUTA
NC
GND NC NC NC GND GND GND NC GND VCC L2A 33nH OR 270nH (COILCRAFT 0603CS) C10A 100pF C11A 10F VPOS C8A OPEN
ADL5592
SW2A
SPI_DATA-A
R9A 0
R10A 0
GND
SPI_CLK-A R3A OPEN TP1A VPOS R2A OPEN R1A OPEN TP1A TP2A
SPI_SEL-A
C14A 1000pF C4A 100pF
RF_OUTA
Figure 24. Evaluation Board Schematic
Rev. 0 | Page 16 of 20
06662-023
C5A R4A 0.1F 0
VPOS
ADL5592
Figure 25. Evaluation Board Layout, Component Side
Figure 26. Evaluation Board Layout, Circuit Side
Rev. 0 | Page 17 of 20
06662-025
06662-024
ADL5592
CONFIGURATION OPTIONS
Table 6. Evaluation Board Configuration Options
Component Designator TP1A, TP2A L1A, L2A, C4A to C11A, R4A, R5A Component Name Supply and ground vector pins Power supply decoupling Description The nominal power supply decoupling is accomplished by using a 100 pF (C4A, C6A, and C10A) in addition to either a 0.1 F (C5A and C7A) or a 10 F (C11A) capacitor at each power supply pin. A series inductor, L2A, is used to bias the open collector at Pin 21. To tune the ADL5592 for the low bands (450 MHz, 850 MHz, and 900 MHz), the value should be 270 nH. For the high bands (1800 MHz and 1900 MHz), the inductor should be changed to 33 nH. Default Conditions Not applicable L2A = 270 nH or 33 nH (Size 0603) (Coilcraft 0603CS); C4A, C6A, C10A = 100 pF (Size 0402); C5A, C7A = 0.1 F (Size 0402); C11A = 10 F (Size 0402); R4A, R5A = 0 (Size 0402); C8A, C9A = open (Size 0402) C14A, C17A = 1000 pF (Size 0402) C1A = 1000 pF (Size 0402); C2A, C3A = 0.1 F (Size 0402)
C14A, C17A
Input and output interfaces
C1A to C3A
Mixer input and output interfaces
SW1A, SW2A, R8A, R12A
Loopback enable interface
R1A to R3A, R9A to R11A
Serial control interface
C14A and C17A are dc blocks. The SMA labeled IN_ATTA is used to drive the RF input. The SMA labeled RF_OUTA corresponds to the RF output. C1A to C3A are dc blocks. The SMA labeled LOPA drives the balanced differential mixer input with a single-ended LO source. The unused differential input is ac-coupled to ground. The SMA labeled MX_OUTA corresponds to the mixer output. To use this function, the loopback mode must be enabled. Normal transmit mode is exercised by applying a logic high voltage to the LOOP EN pin, setting Switch SW1A to the position opposite Label O. For loopback mode, a logic low voltage must be applied to the LOOP EN pin by setting both Switch SW1A and Switch SW2A to the positions closest to the O labels. To exercise the control function from an external source, Switch SW1A must be set to the position closest to the O label and Switch SW2A must be set to the opposite position. The signal is driven from the LBENBA SMA. The evaluation board can be controlled using most PCs. Windows(R)based control software is shipped with the evaluation kit. A 25-pin D-subadapter and cable are required to connect the PC to the SPI port test points on the evaluation board. In some cases, the quality of the PC port signals can be improved by adding capacitance to R1A to R3A. The addition of 50 values for R1A to R3A allow for SPI port control from digital generators driven from the SMAs connectors, SPI_DATA-A, SPI_CLK-A, and SPI_SEL-A.
SW1A, SW2A = installed; R8A = 0 (Size 0402); R12A = 10 k (Size 0402)
R1A, R2A, R3A = open (Size 0402); R9A, R10A, R11A = 0 (Size 0402)
Rev. 0 | Page 18 of 20
ADL5592 OUTLINE DIMENSIONS
INDEX AREA 6.00 BSC SQ
31 30 40 1
PIN 1 INDICATOR
0.50 BSC
EXPOSED PAD
4.25 4.15 SQ 4.00
10 11
TOP VIEW 0.80 0.75 0.70 SEATING PLANE 0.30 0.25 0.18
0.50 0.40 0.30
21 20
BOTTOM VIEW
0.20 MIN
0.05 MAX 0.02 NOM 0.20 REF
THE EXPOSED METAL PADDLE ON THE BOTTOM OF THE LFCSP PACKAGE MUST BE SOLDERED TO PCB GROUND FOR PROPER HEAT DISSIPATION AND ALSO FOR NOISE AND MECHANICAL STRENGTH BENEFITS.
061108-A
COMPLIANT TO JEDEC STANDARDS MO-220-WJJD-2
Figure 27. 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 6 mm x 6 mm Body, Very Very Thin Quad (CP-40-2) Dimensions shown in millimeters
ORDERING GUIDE
Model ADL5592ACPZ-R7 1 ADL5592-EVALZ1
1
Temperature Range -40C to +85C
Package Description 40-Lead LFCSP_WQ, 7" Tape and Reel Evaluation Board
Package Option CP-40-2
Ordering Quantity 3,000
Z = RoHS Compliant Part.
Rev. 0 | Page 19 of 20
ADL5592 NOTES
(c)2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06662-0-6/08(0)
Rev. 0 | Page 20 of 20

▲Up To Search▲

Price & Availability of ADL5592-EVALZ

	To Download ADL5592-EVALZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .